Помогите подключить ИК-порт в линукс х64 минт 17.2 мате.

[Dmitriy 55]

здравствуйте.

Команды даны же на странице после входа в директорию lirc-0.9.0~pre1 -три последовательно,протом пересборка пакета,системе не будет ничё,но лучше все-таки найти где-нибудь нормальный com port и только настроившись пробовать,нет старой машины?

Там описан способ установки этого патча с последующей сборкой Lirc из сорцов. У меня Лирц уже установлен из репов, поэтому какой смысл сносить нормальный пакет который автоматически обновляется системой и ставить неизвестно как работающий такой же пакет только собранный неизвестно как и который нужно будет обновлять вручную. Может возможно этот патч установить на уже установленный Лирц?
Что касается старой машины с COM- портом. У меня только ноутбук с 3 USB портами и с линуксом. На работе с одним парнем попробуем проверить этот приемник через COM и потом через переходник но там только винда стоит. Это будет полезно т.к. буду точно уверен что схема рабочая и все проблеммы из-за этой глючной программы.

[Dmitriy 55]

Здравствуйте.
На днях проверил я свой ИК-приемник/передатчик на работе от СОМ-порта при помощи программы WINLIRC все работает нормально есть и передача и прием от пульта (в окне программы появляются буквы и цифры). С переходником тишина. Скачивал я разные варианты драйверов этого переходника для линукса, но ни один из них так и не смог установить (кстати в интернете многие пишут о том, что они не ставятся). Если кому-то будет интересно я могу их выслать для лабораторных исследований и молекулярно-генетического анализа патологий этого штампа "драйвера"
По поводу поддержки этого переходника ядром, похоже в версии ядра 4.1.5-040105-generic она уже есть т.к. в /lib/modules/4.1.5-040105-generic/kernel/drivers/usb/serial/cp210x.ko есть файл cp210x.ko который собственно и устанавливается при помощи тех же драйверов.
Вот текст описания установки одного из вариантов тех драйверов:

Код: Выделить всё

This bundle contains a modified CP210x driver for the 3.13.0 kernel (Ubuntu 14.04).

It contains:

- Fix for CP2104, now sets the baudrate via "SET_BAUDRATE/GET_BAUDRATE" command
- Fix for CP2105, now stores the interface number for the device for multi interface support
- Fix to support GPIO on all parts
- Fix to correct control request for MHS, Line Control and Break support

NOTE: This driver is an example of how to perform GPIO operations within the CP210x driver since
the driver on kernel.org does not support GPIO at this time. This driver has only been written
and tested on the Linux 3.13.0 kernel on Ubuntu 14.04. This driver is a modified version of the
existing driver in the Linux 3.13.0 kernel, which is maintained at kernel.org. It is recommened
to use the driver there that matches your specific kernel version:

http://www.kernel.org

Build instrutions:

Ubuntu:
1. make ( your cp210x driver )
2. cp cp210x.ko to /lib/modules/<kernel-version>/kernel/drivers/usb/serial
3. insmod /lib/modules/<kernel-version/kernel/drivers/usb/serial/usbserial.ko
4. insmod cp210x.ko

RedHat:
1. yum update kernel*  //need to update the kernel first otherwise your header won't match
2. yum install kernel-devel kernel-headers  //get the devel and header packages.
3. reboot  //your build link should be fixed after your system come back
4. make ( your cp210x driver )  // should be able to build successfully at this point
5. cp cp210x.ko to /lib/modules/<kernel-version>/kernel/drivers/usb/serial
6a. insmod /lib/modules/<kernel-version/kernel/drivers/usb/serial/usbserial.ko
6. insmod cp210x.ko
7. sudo chmod 666 /dev/ttyUSB0
8. sudo chmod 666 /dev/ttyUSB1


GPIO example:
This shows how to use the two IOCTLs to toggle GPIOs. This sample application simply reads
the GPIO settings from the device, flips it, then writes the new setting.

Build instructions:
1. g++ cp210x_gpio_example.c -o cp210x_gpio_example
2. ./cp210x_gpio_example

Как видно из этого описания у меня он уже установлен в ядро. Нужно наверное еще задать какие-то параметры в каких-то конфигурационных файлах для его опознания как эмулятора сом-порта.
Еще я собрал другой переходник по этой ссылке:http://sprinter4wd.narod.ru/poleznye_melochi/usbrs232/ добавив туда согласно даташиту на микросхему переключатель уровня выходного сигнала 5В/ 3,3В. Вот, что выдают lsusb и dmesg :

Код: Выделить всё

dmitriy@dmitriy-RV408-RV508 ~ $ lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 003: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0ac8:c33f Z-Star Microelectronics Corp. Webcam
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 09da:000a A4 Tech Co., Ltd Optical Mouse Opto 510D
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
dmitriy@dmitriy-RV408-RV508 ~ $ 

Код: Выделить всё

[    0.183586] pci 0000:00:1f.3: BAR 0: assigned [mem 0xc0000000-0xc00000ff 64bit]
[    0.183599] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[    0.183603] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    0.183610] pci 0000:00:1c.0:   bridge window [mem 0xf6000000-0xf7ffffff]
[    0.183616] pci 0000:00:1c.0:   bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.183625] pci 0000:00:1c.4: PCI bridge to [bus 04-05]
[    0.183628] pci 0000:00:1c.4:   bridge window [io  0x3000-0x3fff]
[    0.183634] pci 0000:00:1c.4:   bridge window [mem 0xf8000000-0xf9ffffff]
[    0.183640] pci 0000:00:1c.4:   bridge window [mem 0xf2000000-0xf3ffffff 64bit pref]
[    0.183648] pci 0000:00:1c.5: PCI bridge to [bus 06-07]
[    0.183652] pci 0000:00:1c.5:   bridge window [io  0x4000-0x4fff]
[    0.183658] pci 0000:00:1c.5:   bridge window [mem 0xfa000000-0xfbffffff]
[    0.183664] pci 0000:00:1c.5:   bridge window [mem 0xf4000000-0xf5ffffff 64bit pref]
[    0.183672] pci 0000:00:1e.0: PCI bridge to [bus 08]
[    0.183688] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.183691] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.183693] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.183696] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff window]
[    0.183698] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff window]
[    0.183701] pci_bus 0000:00: resource 9 [mem 0xc0000000-0xfebfffff window]
[    0.183704] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.183706] pci_bus 0000:02: resource 1 [mem 0xf6000000-0xf7ffffff]
[    0.183708] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.183711] pci_bus 0000:04: resource 0 [io  0x3000-0x3fff]
[    0.183713] pci_bus 0000:04: resource 1 [mem 0xf8000000-0xf9ffffff]
[    0.183716] pci_bus 0000:04: resource 2 [mem 0xf2000000-0xf3ffffff 64bit pref]
[    0.183718] pci_bus 0000:06: resource 0 [io  0x4000-0x4fff]
[    0.183721] pci_bus 0000:06: resource 1 [mem 0xfa000000-0xfbffffff]
[    0.183723] pci_bus 0000:06: resource 2 [mem 0xf4000000-0xf5ffffff 64bit pref]
[    0.183726] pci_bus 0000:08: resource 4 [io  0x0000-0x0cf7 window]
[    0.183728] pci_bus 0000:08: resource 5 [io  0x0d00-0xffff window]
[    0.183731] pci_bus 0000:08: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.183733] pci_bus 0000:08: resource 7 [mem 0x000d4000-0x000d7fff window]
[    0.183736] pci_bus 0000:08: resource 8 [mem 0x000d8000-0x000dbfff window]
[    0.183738] pci_bus 0000:08: resource 9 [mem 0xc0000000-0xfebfffff window]
[    0.183780] NET: Registered protocol family 2
[    0.184029] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.184162] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.184336] TCP: Hash tables configured (established 32768 bind 32768)
[    0.184410] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.184439] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.184575] NET: Registered protocol family 1
[    0.184605] pci 0000:00:02.0: Video device with shadowed ROM
[    0.185954] PCI: CLS 64 bytes, default 64
[    0.186067] Trying to unpack rootfs image as initramfs...
[    0.817942] Freeing initrd memory: 29144K (ffff880034704000 - ffff88003637a000)
[    0.818047] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.818050] software IO TLB [mem 0xb7aa1000-0xbbaa1000] (64MB) mapped at [ffff8800b7aa1000-ffff8800bbaa0fff]
[    0.818114] Simple Boot Flag at 0x37 set to 0x1
[    0.818280] microcode: CPU0 sig=0x1067a, pf=0x80, revision=0xa07
[    0.818288] microcode: CPU1 sig=0x1067a, pf=0x80, revision=0xa07
[    0.818393] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.818433] Scanning for low memory corruption every 60 seconds
[    0.818815] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.818840] Initialise system trusted keyring
[    0.818865] audit: initializing netlink subsys (disabled)
[    0.818890] audit: type=2000 audit(1453738703.816:1): initialized
[    0.819366] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.821820] zpool: loaded
[    0.821823] zbud: loaded
[    0.822030] VFS: Disk quotas dquot_6.6.0
[    0.822087] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.822788] fuse init (API version 7.23)
[    0.822989] Key type big_key registered
[    0.823443] Key type asymmetric registered
[    0.823447] Asymmetric key parser 'x509' registered
[    0.823512] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.823558] io scheduler noop registered
[    0.823562] io scheduler deadline registered (default)
[    0.823611] io scheduler cfq registered
[    0.824385] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.824408] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.824457] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[    0.824458] vesafb: scrolling: redraw
[    0.824461] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.824483] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90000800000, using 3072k, total 3072k
[    0.848516] Console: switching to colour frame buffer device 128x48
[    0.872415] fb0: VESA VGA frame buffer device
[    0.872443] intel_idle: does not run on family 6 model 23
[    0.872781] ACPI: AC Adapter [ADP1] (off-line)
[    0.872878] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.872898] ACPI: Lid Switch [LID0]
[    0.872954] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    0.872958] ACPI: Power Button [PWRB]
[    0.873014] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    0.873017] ACPI: Sleep Button [SLPB]
[    0.873072] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.873074] ACPI: Power Button [PWRF]
[    0.873736] Monitor-Mwait will be used to enter C-1 state
[    0.873742] Monitor-Mwait will be used to enter C-2 state
[    0.873746] Monitor-Mwait will be used to enter C-3 state
[    0.873750] tsc: Marking TSC unstable due to TSC halts in idle
[    0.873761] ACPI: acpi_idle registered with cpuidle
[    0.875591] thermal LNXTHERM:00: registered as thermal_zone0
[    0.875594] ACPI: Thermal Zone [TZ00] (31 C)
[    0.876665] thermal LNXTHERM:01: registered as thermal_zone1
[    0.876668] ACPI: Thermal Zone [TZ01] (31 C)
[    0.876729] GHES: HEST is not enabled!
[    0.876964] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.880473] Linux agpgart interface v0.103
[    0.880609] agpgart-intel 0000:00:00.0: Intel GM45 Chipset
[    0.880642] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    0.880942] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[    0.881164] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    0.882690] ACPI: Battery Slot [BAT1] (battery present)
[    0.884995] brd: module loaded
[    0.886575] loop: module loaded
[    0.886902] libphy: Fixed MDIO Bus: probed
[    0.886906] tun: Universal TUN/TAP device driver, 1.6
[    0.886908] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.886996] PPP generic driver version 2.4.2
[    0.887116] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.887123] ehci-pci: EHCI PCI platform driver
[    0.887305] ehci-pci 0000:00:1a.7: EHCI Host Controller
[    0.887314] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.887330] ehci-pci 0000:00:1a.7: debug port 1
[    0.891247] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
[    0.891270] ehci-pci 0000:00:1a.7: irq 19, io mem 0xfc704800
[    0.900055] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.900139] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.900142] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.900145] usb usb1: Product: EHCI Host Controller
[    0.900147] usb usb1: Manufacturer: Linux 4.1.5-040105-generic ehci_hcd
[    0.900149] usb usb1: SerialNumber: 0000:00:1a.7
[    0.900327] hub 1-0:1.0: USB hub found
[    0.900336] hub 1-0:1.0: 6 ports detected
[    0.900700] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    0.900708] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.900723] ehci-pci 0000:00:1d.7: debug port 1
[    0.904642] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    0.904663] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfc704c00
[    0.916100] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.916154] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.916157] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.916160] usb usb2: Product: EHCI Host Controller
[    0.916162] usb usb2: Manufacturer: Linux 4.1.5-040105-generic ehci_hcd
[    0.916164] usb usb2: SerialNumber: 0000:00:1d.7
[    0.916339] hub 2-0:1.0: USB hub found
[    0.916349] hub 2-0:1.0: 6 ports detected
[    0.916603] ehci-platform: EHCI generic platform driver
[    0.916625] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.916632] ohci-pci: OHCI PCI platform driver
[    0.916651] ohci-platform: OHCI generic platform driver
[    0.916663] uhci_hcd: USB Universal Host Controller Interface driver
[    0.916793] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.916804] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.916814] uhci_hcd 0000:00:1a.0: detected 2 ports
[    0.916851] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[    0.916910] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.916913] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.916915] usb usb3: Product: UHCI Host Controller
[    0.916918] usb usb3: Manufacturer: Linux 4.1.5-040105-generic uhci_hcd
[    0.916920] usb usb3: SerialNumber: 0000:00:1a.0
[    0.917088] hub 3-0:1.0: USB hub found
[    0.917098] hub 3-0:1.0: 2 ports detected
[    0.917321] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.917328] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.917337] uhci_hcd 0000:00:1a.1: detected 2 ports
[    0.917369] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[    0.917430] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.917433] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.917435] usb usb4: Product: UHCI Host Controller
[    0.917437] usb usb4: Manufacturer: Linux 4.1.5-040105-generic uhci_hcd
[    0.917439] usb usb4: SerialNumber: 0000:00:1a.1
[    0.917615] hub 4-0:1.0: USB hub found
[    0.917624] hub 4-0:1.0: 2 ports detected
[    0.917857] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    0.917865] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    0.917874] uhci_hcd 0000:00:1a.2: detected 2 ports
[    0.917899] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00001860
[    0.917959] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.917962] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.917964] usb usb5: Product: UHCI Host Controller
[    0.917966] usb usb5: Manufacturer: Linux 4.1.5-040105-generic uhci_hcd
[    0.917968] usb usb5: SerialNumber: 0000:00:1a.2
[    0.918138] hub 5-0:1.0: USB hub found
[    0.918147] hub 5-0:1.0: 2 ports detected
[    0.918367] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.918374] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    0.918383] uhci_hcd 0000:00:1d.0: detected 2 ports
[    0.918408] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880
[    0.918472] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    0.918475] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.918477] usb usb6: Product: UHCI Host Controller
[    0.918480] usb usb6: Manufacturer: Linux 4.1.5-040105-generic uhci_hcd
[    0.918482] usb usb6: SerialNumber: 0000:00:1d.0
[    0.918654] hub 6-0:1.0: USB hub found
[    0.918662] hub 6-0:1.0: 2 ports detected
[    0.918883] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.918891] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    0.918900] uhci_hcd 0000:00:1d.1: detected 2 ports
[    0.918924] uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018a0
[    0.918981] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    0.918984] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.918986] usb usb7: Product: UHCI Host Controller
[    0.918989] usb usb7: Manufacturer: Linux 4.1.5-040105-generic uhci_hcd
[    0.918991] usb usb7: SerialNumber: 0000:00:1d.1
[    0.919149] hub 7-0:1.0: USB hub found
[    0.919157] hub 7-0:1.0: 2 ports detected
[    0.919387] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.919395] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    0.919404] uhci_hcd 0000:00:1d.2: detected 2 ports
[    0.919437] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0
[    0.919498] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    0.919501] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.919503] usb usb8: Product: UHCI Host Controller
[    0.919505] usb usb8: Manufacturer: Linux 4.1.5-040105-generic uhci_hcd
[    0.919507] usb usb8: SerialNumber: 0000:00:1d.2
[    0.919673] hub 8-0:1.0: USB hub found
[    0.919681] hub 8-0:1.0: 2 ports detected
[    0.919880] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PSM1] at 0x60,0x64 irq 1,12
[    0.922698] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.922705] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.922925] mousedev: PS/2 mouse device common for all mice
[    0.923436] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.923471] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.923497] i2c /dev entries driver
[    0.923578] device-mapper: uevent: version 1.0.3
[    0.923686] device-mapper: ioctl: 4.31.0-ioctl (2015-3-12) initialised: dm-devel@redhat.com
[    0.923711] ledtrig-cpu: registered to indicate activity on CPUs
[    0.923920] PCCT header not found.
[    0.924226] NET: Registered protocol family 10
[    0.924520] NET: Registered protocol family 17
[    0.924536] Key type dns_resolver registered
[    0.924996] Loading compiled-in X.509 certificates
[    0.926239] Loaded X.509 cert 'Build time autogenerated kernel key: 46fd0f30f3bd8f146803e982177aac2d077a899c'
[    0.926258] registered taskstats version 1
[    0.929010] Key type trusted registered
[    0.934044] Key type encrypted registered
[    0.934057] AppArmor: AppArmor sha1 policy hashing enabled
[    0.934062] ima: No TPM chip found, activating TPM-bypass!
[    0.934099] evm: HMAC attrs: 0x1
[    0.934620]   Magic number: 0:815:338
[    0.934666] thermal thermal_zone1: hash matches
[    0.934678] tty tty59: hash matches
[    0.934786] rtc_cmos 00:03: setting system clock to 2016-01-25 16:18:24 UTC (1453738704)
[    0.934893] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.934895] EDD information not available.
[    0.934991] PM: Hibernation image not present or could not be loaded.
[    0.935691] Freeing unused kernel memory: 1424K (ffffffff81d38000 - ffffffff81e9c000)
[    0.935697] Write protecting the kernel read-only data: 12288k
[    0.935999] Freeing unused kernel memory: 124K (ffff8800017e1000 - ffff880001800000)
[    0.936314] Freeing unused kernel memory: 316K (ffff880001bb1000 - ffff880001c00000)
[    0.954760] systemd-udevd[104]: starting version 204
[    0.957221] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    0.987939] [drm] Initialized drm 1.1.0 20060810
[    1.009455] sky2: driver version 1.30
[    1.009987] sky2 0000:04:00.0: Yukon-2 FE+ chip revision 0
[    1.011868] sky2 0000:04:00.0 eth0: addr 00:24:54:c4:a6:db
[    1.022176] [drm] Memory usable by graphics device = 2048M
[    1.022183] checking generic (d0000000 300000) vs hw (d0000000 10000000)
[    1.022185] fb: switching to inteldrmfb from VESA VGA
[    1.022217] Console: switching to colour dummy device 80x25
[    1.022510] [drm] Replacing VGA console driver
[    1.030329] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.030334] [drm] Driver supports precise vblank timestamp query.
[    1.030438] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    1.110169] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    1.111220] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input7
[    1.111811] [drm] Initialized i915 1.6.0 20150327 for 0000:00:02.0 on minor 0
[    1.111862] ahci 0000:00:1f.2: version 3.0
[    1.112269] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    1.112309] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[    1.112313] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs 
[    1.137489] scsi host0: ahci
[    1.137665] scsi host1: ahci
[    1.137812] scsi host2: ahci
[    1.137954] scsi host3: ahci
[    1.138104] scsi host4: ahci
[    1.138258] scsi host5: ahci
[    1.138338] ata1: SATA max UDMA/133 abar m2048@0xfc704000 port 0xfc704100 irq 29
[    1.138342] ata2: SATA max UDMA/133 abar m2048@0xfc704000 port 0xfc704180 irq 29
[    1.138344] ata3: DUMMY
[    1.138345] ata4: DUMMY
[    1.138348] ata5: SATA max UDMA/133 abar m2048@0xfc704000 port 0xfc704300 irq 29
[    1.138352] ata6: SATA max UDMA/133 abar m2048@0xfc704000 port 0xfc704380 irq 29
[    1.188045] [drm] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
[    1.233369] fbcon: inteldrmfb (fb0) is primary device
[    1.280042] usb 1-4: new high-speed USB device number 3 using ehci-pci
[    1.356037] usb 3-1: new low-speed USB device number 2 using uhci_hcd
[    1.427618] usb 1-4: New USB device found, idVendor=0ac8, idProduct=c33f
[    1.427620] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.427621] usb 1-4: Product: WebCam SCB-0340N
[    1.427623] usb 1-4: Manufacturer: Namuga.
[    1.460081] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.465965] ata1.00: ATA-8: SAMSUNG HM321HI, 2AJ10002, max UDMA/133
[    1.465967] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.471890] ata1.00: configured for UDMA/133
[    1.529117] usb 3-1: New USB device found, idVendor=09da, idProduct=000a
[    1.529119] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.529121] usb 3-1: Product: PS/2+USB Mouse
[    1.529122] usb 3-1: Manufacturer: A4Tech
[    1.546251] hidraw: raw HID events driver (C) Jiri Kosina
[    1.561198] usbcore: registered new interface driver usbhid
[    1.561199] usbhid: USB HID core driver
[    1.563466] input: A4Tech PS/2+USB Mouse as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.0/0003:09DA:000A.0001/input/input8
[    1.563634] a4tech 0003:09DA:000A.0001: input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:1a.0-1/input0
[    1.816073] clocksource tsc: mask: 0xffffffffffffffff max_cycles: 0x1e3115e1c12, max_idle_ns: 440795247804 ns
[    1.873854] psmouse serio1: elantech: assuming hardware version 2 (with firmware version 0x040215)
[    1.910844] psmouse serio1: elantech: Synaptics capabilities query result 0x08, 0x14, 0x0c.
[    2.032148] Console: switching to colour frame buffer device 170x48
[    2.035384] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    2.035386] i915 0000:00:02.0: registered panic notifier
[    2.036248] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM321HI  0002 PQ: 0 ANSI: 5
[    2.036605] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    2.036614] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.036653] sd 0:0:0:0: [sda] Write Protect is off
[    2.036656] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.036685] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.051348] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6
[    2.187957]  sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 >
[    2.188946] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.360068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.361859] ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633J, SC00, max UDMA/100
[    2.362448] ata2.00: configured for UDMA/100
[    2.366286] scsi 1:0:0:0: CD-ROM            TSSTcorp CDDVDW TS-L633J  SC00 PQ: 0 ANSI: 5
[    2.387779] sr 1:0:0:0: [sr0] scsi3-mmc drive: 16x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.387782] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.387964] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.388083] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.708063] ata5: SATA link down (SStatus 0 SControl 300)
[    3.028087] ata6: SATA link down (SStatus 0 SControl 300)
[    3.801138] random: nonblocking pool is initialized
[    5.091393] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    6.575008] init: ureadahead main process (272) terminated with status 5
[    7.949013] Adding 976556k swap on /dev/sda8.  Priority:-1 extents:1 across:976556k FS
[    9.291410] systemd-udevd[387]: starting version 204
[   10.416990] usbcore: registered new interface driver usbserial
[   10.417012] usbcore: registered new interface driver usbserial_generic
[   10.417030] usbserial: USB Serial support registered for generic
[   10.731616] lp: driver loaded but no devices found
[   10.795974] ppdev: user-space parallel port driver
[   12.257211] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   12.595466] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20150410/utaddress-254)
[   12.595475] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.595480] ACPI Warning: SystemIO range 0x00000000000011B0-0x00000000000011BF conflicts with OpRegion 0x0000000000001180-0x00000000000011FF (\GPIO) (20150410/utaddress-254)
[   12.595484] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.595486] ACPI Warning: SystemIO range 0x0000000000001180-0x00000000000011AF conflicts with OpRegion 0x0000000000001180-0x00000000000011FF (\GPIO) (20150410/utaddress-254)
[   12.595490] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.595492] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   13.078330] cfg80211: Calling CRDA to update world regulatory domain
[   13.332312] device-mapper: multipath: version 1.9.0 loaded
[   13.630638] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269VB: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   13.630644] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   13.630647] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[   13.630649] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   13.630651] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   13.630654] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x19
[   13.630657] snd_hda_codec_realtek hdaudioC0D0:      Mic=0x18
[   13.639746] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   13.639966] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   13.691448] ath: phy0: Enable LNA combining
[   13.694095] ath: phy0: ASPM enabled: 0x42
[   13.694099] ath: EEPROM regdomain: 0x65
[   13.694100] ath: EEPROM indicates we should expect a direct regpair map
[   13.694103] ath: Country alpha2 being used: 00
[   13.694104] ath: Regpair used: 0x65
[   13.937893] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   13.938448] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc90000780000, irq=17
[   14.260728] samsung_laptop: enabled workaround for brightness stepping quirk
[   14.263144] samsung_laptop: detected SABI interface: SwSmi@
[   14.448542] media: Linux media interface: v0.10
[   14.487992] Linux video capture interface: v2.00
[   14.723333] uvcvideo: Found UVC 1.00 device WebCam SCB-0340N (0ac8:c33f)
[   14.725541] input: WebCam SCB-0340N as /devices/pci0000:00/0000:00:1a.7/usb1/1-4/1-4:1.0/input/input11
[   14.725718] usbcore: registered new interface driver uvcvideo
[   14.725721] USB Video Class driver (1.1.1)
[   15.529418] cfg80211: World regulatory domain updated:
[   15.529424] cfg80211:  DFS Master region: unset
[   15.529425] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   15.529429] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   15.529431] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   15.529434] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[   15.529436] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   15.529439] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   20.324234] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   21.568871] EXT4-fs (sda10): mounted filesystem with ordered data mode. Opts: (null)
[   21.735660] EXT4-fs (sda13): mounted filesystem with ordered data mode. Opts: (null)
[   21.906436] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   22.068721] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[   22.168549] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   22.251250] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[   22.356676] EXT4-fs (sda12): mounted filesystem with ordered data mode. Opts: (null)
[   23.104502] init: failsafe main process (848) killed by TERM signal
[   28.941813] init: cups main process (1062) killed by HUP signal
[   28.941833] init: cups main process ended, respawning
[   28.979138] Bluetooth: Core ver 2.20
[   28.979169] NET: Registered protocol family 31
[   28.979171] Bluetooth: HCI device and connection manager initialized
[   28.979178] Bluetooth: HCI socket layer initialized
[   28.979183] Bluetooth: L2CAP socket layer initialized
[   28.979192] Bluetooth: SCO socket layer initialized
[   29.171466] Bluetooth: RFCOMM TTY layer initialized
[   29.171481] Bluetooth: RFCOMM socket layer initialized
[   29.171490] Bluetooth: RFCOMM ver 1.11
[   29.389478] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   29.389485] Bluetooth: BNEP filters: protocol multicast
[   29.389492] Bluetooth: BNEP socket layer initialized
[   32.437741] lirc_dev: IR Remote Control driver registered, major 248 
[   32.976900] lirc_sir: module is from the staging directory, the quality is unknown, you have been warned.
[   32.977364] platform lirc_dev.0: lirc_dev: driver lirc_sir registered at minor = 0
[   32.977388] lirc_sir: I/O port 0x03e8, IRQ 4.
[   32.977410] lirc_sir: Installed.
[   35.684214] init: samba-ad-dc main process (1151) terminated with status 1
[   35.960601] init: plymouth-upstart-bridge main process ended, respawning
[   35.969271] init: plymouth-upstart-bridge main process (1392) terminated with status 1
[   35.969288] init: plymouth-upstart-bridge main process ended, respawning
[   37.501859] sky2 0000:04:00.0 eth0: enabling interface
[   37.502369] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   37.524421] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   39.214522] sky2 0000:04:00.0 eth0: Link is up at 100 Mbps, full duplex, flow control both
[   39.214541] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   45.024396] NET: Registered protocol family 24
[   58.045782] vboxdrv: module verification failed: signature and/or required key missing - tainting kernel
[   58.051017] vboxdrv: Found 2 processor cores
[   58.053260] vboxdrv: fAsync=0 offMin=0x1c3 offMax=0x2390
[   58.153462] vboxdrv: TSC mode is Synchronous, tentative frequency 2094748818 Hz
[   58.153466] vboxdrv: Successfully loaded version 5.0.12 (interface 0x00240000)
[   58.390000] VBoxNetFlt: Successfully started.
[   58.443917] VBoxNetAdp: Successfully started.
[   58.467989] VBoxPciLinuxInit
[   58.511243] vboxpci: IOMMU not found (not registered)
[   60.303799] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.303814] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.303920] pci_bus 0000:08: Allocating resources
[   60.303933] pci 0000:00:1e.0: bridge window [io  0x1000-0x0fff] to [bus 08] add_size 1000
[   60.303937] pci 0000:00:1e.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 08] add_size 200000 add_align 100000
[   60.303941] pci 0000:00:1e.0: bridge window [mem 0x00100000-0x000fffff] to [bus 08] add_size 200000 add_align 100000
[   60.303944] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.303949] pci 0000:00:1e.0: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[   60.303952] pci 0000:00:1e.0: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[   60.303955] pci 0000:00:1e.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[   60.303958] pci 0000:00:1e.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[   60.303961] pci 0000:00:1e.0: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[   60.303963] pci 0000:00:1e.0: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[   60.303970] pci 0000:00:1e.0: BAR 14: assigned [mem 0xc0100000-0xc02fffff]
[   60.303976] pci 0000:00:1e.0: BAR 15: assigned [mem 0xc0300000-0xc04fffff 64bit pref]
[   60.303982] pci 0000:00:1e.0: BAR 13: assigned [io  0x6000-0x6fff]
[   60.303986] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.303990] pci 0000:00:1e.0:   bridge window [io  0x6000-0x6fff]
[   60.303997] pci 0000:00:1e.0:   bridge window [mem 0xc0100000-0xc02fffff]
[   60.304021] pci 0000:00:1e.0:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[   60.304560] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.304569] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.304574] pci 0000:00:1e.0:   bridge window [io  0x6000-0x6fff]
[   60.304581] pci 0000:00:1e.0:   bridge window [mem 0xc0100000-0xc02fffff]
[   60.304586] pci 0000:00:1e.0:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[   60.304740] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.304745] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.304749] pci 0000:00:1e.0:   bridge window [io  0x6000-0x6fff]
[   60.304756] pci 0000:00:1e.0:   bridge window [mem 0xc0100000-0xc02fffff]
[   60.304761] pci 0000:00:1e.0:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[   60.304890] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.304894] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.304898] pci 0000:00:1e.0:   bridge window [io  0x6000-0x6fff]
[   60.304905] pci 0000:00:1e.0:   bridge window [mem 0xc0100000-0xc02fffff]
[   60.304910] pci 0000:00:1e.0:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[   60.304936] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.304941] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.304945] pci 0000:00:1e.0:   bridge window [io  0x6000-0x6fff]
[   60.304951] pci 0000:00:1e.0:   bridge window [mem 0xc0100000-0xc02fffff]
[   60.304956] pci 0000:00:1e.0:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[   60.305123] pci_bus 0000:02: Allocating resources
[   60.305142] pci_bus 0000:04: Allocating resources
[   60.305184] pci_bus 0000:06: Allocating resources
[   60.305205] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[   60.305209] pci 0000:00:1e.0: PCI bridge to [bus 08]
[   60.305213] pci 0000:00:1e.0:   bridge window [io  0x6000-0x6fff]
[   60.305220] pci 0000:00:1e.0:   bridge window [mem 0xc0100000-0xc02fffff]
[   60.305225] pci 0000:00:1e.0:   bridge window [mem 0xc0300000-0xc04fffff 64bit pref]
[   67.029592] init: plymouth-stop pre-start process (2428) terminated with status 1
[   89.078597] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   89.274572] Netfilter messages via NETLINK v0.30.
[   89.282701] ctnetlink v0.93: registering with nfnetlink.
[   89.404869] ip_tables: (C) 2000-2006 Netfilter Core Team
[  188.433497] perf interrupt took too long (2503 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[ 1616.445638] perf interrupt took too long (5002 > 5000), lowering kernel.perf_event_max_sample_rate to 25000
[ 5967.208089] usb 7-1: new full-speed USB device number 2 using uhci_hcd
[ 5967.369148] usb 7-1: New USB device found, idVendor=10c4, idProduct=ea60
[ 5967.369152] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5967.369155] usb 7-1: Product: CP2102 USB to UART Bridge Controller
[ 5967.369158] usb 7-1: Manufacturer: Silicon Labs
[ 5967.369160] usb 7-1: SerialNumber: 0001
[ 5967.375193] usbserial_generic 7-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.
[ 5967.375198] usbserial_generic 7-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.
[ 5967.375201] usbserial_generic 7-1:1.0: generic converter detected
[ 5967.375344] usb 7-1: generic converter now attached to ttyUSB0
[ 5967.441482] usbcore: registered new interface driver cp210x
[ 5967.442929] usbserial: USB Serial support registered for cp210x
[ 7429.732081] usb 7-1: USB disconnect, device number 2
[ 7429.732301] generic ttyUSB0: generic converter now disconnected from ttyUSB0
[ 7429.732321] usbserial_generic 7-1:1.0: device disconnected
[10144.344080] usb 7-1: new full-speed USB device number 3 using uhci_hcd
[10144.913145] usb 7-1: New USB device found, idVendor=0403, idProduct=6001
[10144.913152] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[10144.913154] usb 7-1: Product: FT232R USB UART
[10144.913157] usb 7-1: Manufacturer: FTDI
[10144.913159] usb 7-1: SerialNumber: A9U9LFFR
[10145.043726] usbcore: registered new interface driver ftdi_sio
[10145.044431] usbserial: USB Serial support registered for FTDI USB Serial Device
[10145.052528] ftdi_sio 7-1:1.0: FTDI USB Serial Device converter detected
[10145.052765] usb 7-1: Detected FT232RL
[10145.060154] usb 7-1: FTDI USB Serial Device converter now attached to ttyUSB0
dmitriy@dmitriy-RV408-RV508 ~ $ 

Вроде все нормально опозналось. Только мне не понятны эти две строчки :

Код: Выделить всё

[ 5967.375193] usbserial_generic 7-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.
[ 5967.375198] usbserial_generic 7-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

Судя по первой строке этот переходник не полностью эмулирует сом-порт, а во второй зачем-то предлагают связаться с kernel.org для добавления этого девайса в поддержку ядра, хотя вроде она и так существует причем и в лирце похоже тоже. При подсоединении моего ик- приемника/передатчика почему-то все время светится светодиод передачи хотя при проверке от сом-порта в винде и от всторого переходника такого явления не наблюдалось. Переключение уровня выходного сигнала ничего не меняет.
Хотел я протестировать через заглушку эти переходники на прием и передачу при помощи программ CuteCom и minicom но первая абсолютно не работает несмотря на то, что ставится из репов, а во второй я указываю там свой переходник как ttyUSB0 сохраняю файл как fdi и выхожу (при этом я проверил, что файл действительно создался и в нем указан именно мой этот интерфейс) но при запуске minicom всеравно почему-то выводится интерфейс ttyS0 и не происходит никакой реакции на нажатия клавиш. Похоже пока я не запущу нормальную работу хоть одного из этих переходников, дальше двигаться нет смысла. Куда еще копать я уже не знаю.
На днях посмотрю работу этого переходника в винде и попробую свою самоделку с ним, если там все заработает нормально, останется только писать только в kernel.org за помощью в решении этой прблеммы.

[ALEXX]

останется только писать только в kernel.org за помощью в решении этой прблеммы.

Попробуй, может действительно помогут... В прекрасное далеко точно не пошлют , хотя ожидание может быть долгим

[Dmitriy 55]

Здравствуйте.
За прошедшее время мне удалось только запустить свой самодельный переходник на FT232RL микросхеме в WINE и проверить его работу с помощью заглушки и программы SerialNetTools все передается и принимается как часы. Сам порт определился как Com2. B Самом линуксе пока никаких подвижек.
Программа CuteCom вообще не открывает ни один из портов.
Может возможно как-то организовать управление от ИК-порта через виндовский лирц+ Wine? Кто-то имел опыт такого извращенного управления? опишите пожалуйста как все это организовать.
С покупным переходником ВМ8050 вообще тишина. Он не запускается ни в винде (не смотря на установку его драйверов) ни в линуксе. Описал эту проблемму и отправил производителю, пока в ответ тишина. Видимо ни только у меня с ним проблеммы .
Просьба подскажите, как настроить управление компом через связку WINLIRC + Wine. Также, где можно найти методику настройки лирц для управления отдельными приложениями (например: запуск и управление проигрывателями VLC и Totem, RadioTray, управление внешним USB тв тюнером)
Спасибо.